Skip to Content
← Back

NCU-OPS-BASIC · SINUMERIK ONE

NCU Operator System
Basic CNC

A SINUMERIK ONE PPU 1740 and its width-matched machine control panel, mounted and wired in a Type 12 rear-access operating housing. Pick the screen, pick how it hangs or stands, land 24 V DC and PROFINET, and the machine has its operator station.

  • PPU 1740 all-in-oneCNC, HMI, S7-1500F PLC and a 15.6″ or 19″ multitouch display in one unit
  • Matched SINUMERIK ONE MCPE-Stop, integral handwheels, feed and spindle override, USB, same width as the PPU
  • Rittal AX operating housing600 x 600 x 210, 3 mm aluminum front plate machined to the Siemens cutouts, Type 12
  • Arm, wall or pedestalRittal CP 120 support arm from above or the wall, or a floor pedestal, fixed or on casters
  • Pre-wired24 V DC, PE and the PROFINET patch between MCP and PPU are done; field lands one supply and one network cable
  • Built and tested in NCFunction test, E-Stop chain, handwheels, closed-door heat run, 3-year warranty on the assembly
 

The same SINUMERIK Operate HMI that runs on the PPU 1740, simulated here so you can try the keys.

Configure your station

Screen

Mounting

Housing

Cooling

Cable exit

Handheld MPG

Keyboard

Software

Build ID
Estimated list

Estimate for the configuration shown, before Siemens software licenses. We confirm price and lead time with the quote.

Request this configuration

Want just the station? Choose the screen size above the price and add it to the cart; mounting and options are quoted.

Specification

What ships

    Not included: SINUMERIK ONE system software and licenses, the CF card, drives and motors, and the machine PLC program. Think-PLC engineering loads and commissions on request.

    What the NCU inside can do

    Axes and spindles

    • Up to 12 NC axes per PPU 1740, servo and spindle, on SINAMICS S120 via DRIVE-CLiQ
    • Grow the axis group with NX10.3 (+3 axes) or NX15.3 (+6 axes) modules
    • 1FT/1FK servo, 1PH/1FE/2SP1 spindle, 1FN3 linear and 1FW6 torque motors
    • Up to three handwheels, two on the PPU and one on the MCP

    G-code and programming

    • DIN 66025 G-code with the SINUMERIK high-level language: R-parameters, frames, loops, subprograms
    • ISO dialect mode runs programs written for other controls with minimal edits
    • ShopMill / ShopTurn work-step programming and programGUIDE cycles for drilling, milling, turning and measuring
    • Simulation on the panel before the first cut; Run MyVirtual Machine for the office

    PLC, safety and network

    • SIMATIC S7-1500F PLC inside, engineered in TIA Portal V15 or later
    • Safety Integrated with PROFIsafe V2: safe stop, safe limited speed, safe door monitoring
    • PROFINET IO controller for up to 128 devices on X160, 255 on X150 from V6.15
    • OPC UA server for MES and data collection; PROFINET IRT for isochronous drives

    Operator interface

    • SINUMERIK Operate on a 15.6″ 1366 x 768 or 19″ 1920 x 1080 multitouch glass front, IP65
    • Machine control panel with mechanical keys, E-Stop, override switches and USB on the front
    • Run MyScreens for custom screens, Run MyRobot for a robot in the same G-code
    • Two Ethernet ports, USB, CF card slot behind the front, all reachable from the rear door

    How it is built

    Front plate machiningCutouts and MCP stud holes cut in the 3 mm plate, both faces deburred, outside face protected.
    Housing prepDoor-to-body ground strap, arm connection oriented for the mount (down for a pedestal), gland plate when cables run externally.
    Device mountingPPU from the front on its spring retainers and clamps (0.5 Nm); MCP on M5 studs (1.5 Nm) or tension jacks (0.4 Nm). 25 mm bezel gap.
    Wiring24 V DC to the PPU terminal-kit connector and the MCP, PROFINET patch, labeled field terminals, cables dressed clear of the PPU airflow.
    Load and testSystem software if ordered, MCP device name, E-Stop chain, handwheel pulses, overrides, 30-minute closed-door heat run.
    Clean, label, packNameplate with build ID and serial on the rear door, screen protector left on, arm connection covered for shipping.
    SINUMERIK ONEDigital-native CNC, TIA Portal engineered
    Type 12 housingRittal AX with rear service access
    Made in NCAssembled and tested in Winston-Salem
    3-year warrantyOn the Think-PLC assembly

    Documentation and downloads

    Datasheet Rev APDF, specs, build steps, plate cutouts STEP modelOn request, per configuration Drawing packagePlate DXF, wiring, arm layout, on request
    1. All Products
    2. All Products
    3. NCU Operator System - Basic CNC
    35% Markup

    NCU Operator System - Basic CNC

    Part Number NCU-OPS-BASIC
    https://think-plc.com/web/image/product.template/332045/image_1920?unique=50fec92

    SINUMERIK ONE PPU 1740 panel processing unit (15.6″ or 19″ multitouch, NCU + S7-1500F PLC in one unit) over a width-matched SINUMERIK ONE machine control panel with E-Stop and integral handwheels, both mounted in a machined 3 mm aluminum plate on a Rittal AX 600 x 600 x 210 Type 12 rear-access operating housing. 24 V DC, PE and the MCP-to-PPU PROFINET patch are pre-wired; hang it on a support arm or pedestal and land one supply and one network cable.

    • NCU-OPS-BASIC-15: PPU 1740-1500 + MCP 1500 (two handwheels)
    • NCU-OPS-BASIC-19: PPU 1740-1900 + MCP 1900
    • System software, CF card, drives, arm/pedestal not included
    • Assembled and tested in Winston-Salem, NC; 3-year warranty on the assembly

    $ 19,450.00 19450.0 USD $ 19,450.00 Tax Excluded

    Call for price

    • Screen Size

    This combination does not exist.

    Contact Us

    Shar